多種のプラスチック成品を製造し、最大射出機械は650トンです
UL / ISO 9001認証プラスチック射出工場
すべての射出機には、高い安全性、高い効率、高い安定した生産のためにロボットアームが装備されていました
中央搬送と自動供給システムにより、クリーンと自動制御の射出成形が可能になります
: ロボットアーム
FEATURES | THERMAL | ||||
GENERIC | COMMON NAME | HEAT DISTORTION TEMPERATURE | CONTINOUS HEAT TEMPERATURE | THERMAL EXPANSION COEFFICIENT | HEAT TRANSFER ARC RESISTANCE |
Test Mode | ASTM | D648 | Long Time | D696 | CI77 |
Units | ℃(46kg/cm2) | ℃ | 105/℃ | 10-4cal Sec cm /℃ cm | |
PVC | 氯乙烯 | 80 | 65-75 | 7-25 | 3.0-7.0 |
CPVC | 氯乙烯 | 95-112 | 99 | 6.8-7.6 | 3.3 |
HDPE | 聚乙烯 | 43-54 | 80 | 11-13 | 11-12.4 |
UPE | 乙烯鋼 | 91 | 120 | 12 | 11-12.4 |
PVDF | 鐵氟龍2F | 160 | 150 | 12 | 3 |
PTFE | 鐵氟龍4F | 240-245 | 290 | 10 | 6 |
PETP | 聚酯膠 | 180 | 100 | 2.2 | 3.36 |
PP | 聚丙烯 | 99-104 | 85 | 6-8.5 | 2.8 |
AP-6 | 尼龍6 | 67-70 | 79-121 | 8.3 | 5.85 |
AP-66 | 尼龍66 | 66-104 | 82-150 | 8 | 5.885 |
MC | MC尼龍 | 149-219 | 121-149 | 9 | X |
FEATURES | THERMAL | ||||
GENERIC | COMMON NAME | HEAT DISTORTION TEMPERATURE | CONTINOUS HEAT TEMPERATURE | THERMAL EXPANSION COEFFICIENT | HEAT TRANSFER ARC RESISTANCE |
Test Mode | ASTM | D648 | Long Time | D696 | CI77 |
Units | ℃(46kg/cm2) | ℃ | 105/℃ | 10-4cal Sec cm /℃ cm | |
POM | 塑膠鋼 | 110 | 80-120 | 8.5 | 5.5 |
PPS | 聚苯橕硫 | 230 | 220 | ||
PU | 優力膠 | ||||
PSU | 聚硐 | 180 | 150 | ||
PBI | 聚苯並咪唑 | ||||
PI VESPEL | 聚酰亞胺 | ||||
ABS | 丁二烯 | 94-107 | 60-110 | 6-13 | 4.6-8.6 |
PMMA | 壓克力 | 74-102 | 71-85 | 5-9 | 4-6 |
PC | 聚碳酸酯 | 130-140 | 120 | 6.6 | 4.6 |
PEEK | 聚醚醚酮 | 250 | 160 | 1.4 | 2.2 |
BAKELITE | 電木 | X | 150 | 1.4 | 4.9 |
FRP | 玻璃纖維 | 139-278 | 180 | 1.1-3.5 | 4-10 |
FEATURES | PHYSICAL | ||||||
GENERIC | COMMON NAME | PROPORTION | IN THEIR ORIGINAL APPEARANCE | WATER ABSORPTION | CHANGES WHEN EXPOSED TO LIGHT | MACHINABILITY | YUDEN RATE |
Test Mode | ASTM | D790 | Common Materials | D572 | D150 | ||
單位 | Target | 24Hrs % | 1KHz | ||||
PVC | 氯乙烯 | 1.45 | Gray | 0.07-0.4 | easy to aging | ◎ | 200 |
CPVC | 氯乙烯 | 1.65 | Mouse Grey | <0.05 | gradually aging | ◎ | X |
HDPE | PE | 1 | White | <0.01 | long-term aging | ◎ | 2.3-2.35 |
UPE | 乙烯鋼 | 1 | White | <0.01 | long-term aging | ◎ | 2.2 |
PVDF | 鐵氟龍2F | 1.8 | White | 0.04 | Unchanged | ◎ | 8.0 |
PTFE | 鐵氟龍4F | 2.2 | White | <0.01 | Unchanged | ◎ | 2.0 |
PETP | 聚酯膠 | 1.38 | White | 0.3 | Unchanged | ◎ | X |
PP | 聚丙烯 | 1 | White | 0.02-0.03 | long-term aging | ○ | 2.65 |
Note: ◎Excellent ○Be △Fair ╳Poor
FEATURES | PHYSICAL | ||||||
GENERIC | COMMON NAME | PROPORTION | IN THEIR ORIGINAL APPEARANCE | WATER ABSORPTION | CHANGES WHEN EXPOSED TO LIGHT | MACHINABILITY | YUDEN RATE |
Test Mode | ASTM | D790 | Common Materials | D572 | D150 | ||
單位 | Target | 24Hrs % | 1KHz | ||||
AP-6 | 尼龍6 | 1.15 | White | 1.6 | Yellow | ○ | 4.0-4.9 |
AP-66 | 尼龍66 | 1.15 | Light earth tones | 1.5 | Yellow | ○ | 3.9-4.5 |
MC | MC尼龍 | 1.15 | White | 0.6-2.0 | Yellow | ○ | 3-7 |
POM | 塑膠鋼 | 1.42 | White | 0.22 | long-term aging | ◎ | 3.8 |
ABS | 丁二烯 | 1.07 | translucent | 0.1-0.8 | easy to aging | ○ | 2.4-4.75 |
PMMA | 壓克力 | 1.20 | translucent | 0.3-0.4 | easy to aging | ○ | 3.0-3.5 |
PC | 聚碳酸酯 | 1.20 | Dark brown | 0.15 | Unchanged | ◎ | 3.02 |
PEEK | 聚醚醚酮 | 1.26-1.32 | black | 0.14 | long-term aging | ◎ | 3.4 |
BAKELITE | 電木 | 1.5 | Brown | 1.5 | Unchanged | △ | X |
FRP | 玻璃纖維 | 2.0 | Light gray | 0.1-1.0 | Unchanged | X | X |
Note: ◎Excellent ○Be △Fair ╳Poor
FEATURES | MECHANICAL | ||||||||
GENERIC | COMMON NAME | HARDNESS | TENSILE STRENGTH | ELONGATION | TENSILE ELASTIC MODULUS | COMPRESSIVE STRENGTH | BENDING STRENGTH | IMPACT STRENGTH | |
Test Mode | ASTM | D785 | D638 | D695 | D790 | IZOD | |||
Units | kg/cm2 | ||||||||
PVC | 氯乙烯 | R108-118 | 350-630 | 2.0-4.0 | 2.5-4.2 | 560-910 | 200 | 1.0-3.0 | |
CPVC | 氯乙烯 | R117-122 | 527-633 | 4.5-6.5 | 2.53-3.34 | 633-1550 | X | 5.44-30.5 | |
HDPE | 聚乙烯 | R38-50 | 220-390 | 15-100 | 0.42-1.00 | 330 | 2.3-2.35 | 8.2-10.9 | |
UPE | 乙烯鋼 | R40-50 | 400-470 | 300-500 | 0.20-1.10 | 230 | 2.2 | 不破壞 | |
PVDF | 鐵氟龍2F | SHORE D 80 | 490 | 100-300 | 0.84 | 700 | 8.0 | 19.0 | |
PTFE | 鐵氟龍4F | SHORE D 50-60 | 140-320 | 200-400 | 0.41 | 120 | 2.0 | 16.4 | |
PETP | 聚酯膠 | M70-115 | 1200-1760 | 70-130 | 3.2-4.2 | 914-211 | X | 70 | |
PP | 聚丙烯 | R90-100 | 350-360 | 3-20 | 2.1-3.6 | 490 | 2.65 | 2.2-16.3 |
FEATURES | MECHANICAL | ||||||||
GENERIC | COMMON NAME | HARDNESS | TENSILE STRENGTH | ELONGATION | TENSILE ELASTIC MODULUS | COMPRESSIVE STRENGTH | BENDING STRENGTH | IMPACT STRENGTH | |
Test Mode | ASTM | D785 | D638 | D695 | D790 | IZOD | |||
Units | kg/cm2 | ||||||||
AP-6 | 尼龍6 | R103-118 | 490-860 | 2.5-320 | 1.1-2.7 | 500-910 | 4.0-4.9 | 5.5-19.6 | |
AP-66 | 尼龍66 | R108-118 | 630-840 | 60-300 | 1.2-2.9 | 470-880 | 3.9-4.5 | 5.5-10.9 | |
MC | MC尼龍 | R112-120 | 670-840 | 360-320 | 3.5-4.5 | 770-980 | 3-7 | 223 | |
POM | 塑膠鋼 | M78-80 | 620 | 60-75 | 2.8 | 1120 | 3.8 | 6.5-7.6 | |
ABS | 丁二烯 | R80-118 | 170-630 | 10-140 | 0.7-2.9 | 188-177 | 250-950 | 3.8-66 | |
PMMA | 壓克力 | M84-105 | 490-770 | 2-10 | 3.2 | 840-0 | 900-1300 | 2.6-7 | |
PC | 聚碳酸酯 | M70-R118 | 560-670 | 60-100 | 2.5 | 880 | 950 | 65-87 | |
PEEK | 聚醚醚酮 | SHORE D 88 | X | 50 | 1.1 | 900 | 1700 | 8.3 | |
BAKELITE | 電木 | E79-82 | 211-633 | 0.37-0.57 | X | 17-35 | 1200-1500 | 2.0-4.0 | |
FRP | 玻璃纖維 | M100-105 | 1400-4200 | 4 | 14-28 | 3500-4900 | 4900-7000 | 109-163 |
FEATURES | CHEMICAL | |||||
GENERIC | COMMON NAME | WEAK ACID CHANGE | ACID CHANGE | WEAK BASE CHANGE | BASE CHANGE | EFFECT OF ORGANIC SOLVENT |
Test Mode | D543 | |||||
PVC | 氯乙烯 | △ | △ | ○ | ○ | ○ |
CPVC | 氯乙烯 | ○ | ○ | ◎ | ◎ | ○ |
HDPE | 聚乙烯 | ◎ | △ | ◎ | ◎ | ○ |
UPE | 乙烯鋼 | ◎ | ◎ | ◎ | ◎ | ◎ |
PVDF | 鐵氟龍2F | ◎ | △ | ◎ | △ | ◎ |
PTFE | 鐵氟龍4F | ◎ | ◎ | ◎ | ◎ | ◎ |
PETP | 聚酯膠 | ◎ | ◎ | ◎ | ◎ | ◎ |
PP | 聚丙烯 | ◎ | △ | ◎ | ◎ | ○ |
AP-6 | 尼龍6 | ○ | X | ◎ | ◎ | ○ |
AP-66 | 尼龍66 | ○ | X | ◎ | ◎ | ○ |
MC | MC尼龍 | ○ | △ | ○ | ○ | ○ |
POM | 塑膠鋼 | △ | X | ◎ | ◎ | ◎ |
ABS | 丁二烯 | ○ | △ | ○ | ○ | X |
PMMA | 壓克力 | ○ | △ | ○ | X | X |
PC | 聚碳酸酯 | ◎ | △ | ○ | X | △ |
PEEK | 聚醚醚酮 | ◎ | ◎ | ◎ | ◎ | ◎ |
BAKELITE | 電木 | △ | △ | △ | △ | △ |
FRP | 玻璃纖維 | △ | △ | △ | △ | △ |
Note: ◎Excellent ○Be △Fair ╳Poor
FEATURES | ELECTRICA | ||||
GENERIC | COMMON NAME | ARC RESISTANCE | DIELECTRIC STRENGTH | DIELECTRIC PROPERTIES | VOLUME RESISTANCE RATIO |
Test Mode | ASTM | D495 | D149 | D150 | D257 |
Units | Sec | kv/mm | 1KHz | Ω-CM | |
PVC | 氯乙烯 | X | 14 | 200 | 1016 |
CPVC | 氯乙烯 | X | 1.22-1.50 | X | 1015 |
HDPE | 聚乙烯 | 200-235 | 17.7-19.7 | 2.3-2.35 | 1016 |
UPE | 乙烯鋼 | X | 50 | 2.2 | 1013 |
PVDF | 鐵氟龍2F | 50-70 | 10.2 | 8.0 | 2 x 1014 |
PTFE | 鐵氟龍4F | >200 | 18.9 | 2.0 | >1013 |
PETP | 聚酯膠 | 125 | 18.0 | X | 1019 |
PP | 聚丙烯 | 120 | 19.7-260 | 2.65 | 2 x 1016 |
AP-6 | 尼龍6 | 135 | 17.3-20.0 | 4.0-4.9 | 1012- 1015 |
AP-66 | 尼龍66 | 130-140 | 15.1-18.5 | 3.9-4.5 | 1014- 1015 |
MC | MC尼龍 | X | 12-20 | 3-7 | 1012- 1015 |
POM | 塑膠鋼 | 240 | 18.3 | 3.8 | 1014 |
ABS | 丁二烯 | 47-87 | 12.2-16.1 | 2.4-4.75 | 1016 |
PMMA | 壓克力 | X | 17.7-21.6 | 3.0-3.5 | >1014 |
PC | 聚碳酸酯 | 10-120 | 15-7 | 3.02 | 2 x 1011 |
PEEK | 聚醚醚酮 | 4.8 | 190 | 3.4 | 5 x 1016 |
BAKELITE | 電木 | 2-130 | 200-400 | X | 5 x 107 |
FRP | 玻璃纖維 | 120-180 | 300-400 | X | >1013 |
High Quality is one of HON HAMN’s policies and to meet severe color specification, HON HAMN does not check color quality by technician's eyes, but we purchased the same brand of premier spectrophotometer as our North America customer has.
Color-Eye 7000A features unsurpassed inter-instrument agreement, superior precision and outstanding reproducibility over time. Precise, repeatable measurements allow HON HAMN to share data globally, making it the instrument of choice for dedicated color analysis in the lab or in a manufacturing setting.
Q1 |
Are you trading company or factory ?
HON HAMN's Headquarter and R&D Dept. is located in Taiwan, and Our Factory is located in Dongguan, GuangDong Province, China. |
Q2 |
I have an idea/ sample but don’t have drawing, what can I do?
Please share the project detail to us, and we can provide ON STOP SERVICE. |
Q3 |
What type of files can you accept?
STP, IGS, DWG, DXF. |
Q4 |
Your trading terms ?
EX-WORKS, FOB, CIF, DDP, DDU |
Q5 |
Your payment terms ?
For plastic injection molds and metal stamping dies : 30% T/T in advance before starting design & 70% T/T before shipment. |
Q6 |
What information should I give to you for inquiry?
1) Product 2D/3D drawing |
Q7 |
What type of plastic injection mold do you make?
We can make the PRODUCTION MOLD, EXPORT MOLD, INSERT MOLD, MULTI-CAVITY MOLD, HOT RUNNER MOLD and FAMILY MOLD. |
Q8 |
How many percent of molds are exported?
75% of the molds we built are exported to USA, Canada, Japan, and Middle East. |
Q9 |
Do you provide samples ? is it free or extra cost?
Before deciding to make the mold, HON HAMN can offer mockup with CNC milling or 3D printing, with extra sample cost and shipping fee. |
Q10 |
What is your advantage?
HH could produce both injection mold and plastic products. Combining the advantages of both design concepts and offer ENGINEERING SOLUTION to optimize the products. With a good quality of mold, a lot of cost can be saved easily. |